The Evolution Power 4.0 pool robot makes cleaning your pool much easier. This automatic pool robot cleans the floor and climbs the walls up to the waterline. This allows it to tackle dirt in multiple areas, so you spend less time cleaning manually. The Power 4.0 is suitable for pools up to 10 x 5 meters with a maximum depth of 2.5 meters.
The robot runs an automatic cleaning cycle of 2 hours. During cleaning, the debris that is sucked up is collected in the debris basket. This is easily accessible, so you can quickly remove and empty the basket after use. This makes it easy to prepare the robot for the next cleaning cycle.
The 13-meter floating cable gives the robot room to move while cleaning. Thanks to the No-Twist swivel coupling, cable twisting is limited. This helps prevent the cable from getting tangled as the robot moves around the pool.
The Evolution Power 4.0 comes including a transformer. This means you are choosing an automatic cleaning aid that combines floor and wall cleaning with practical maintenance.
Build a sturdy and well-insulated foundation for your swimming pool with these high-density polystyrene pool blocks. The 100 x 25 x 30 cm blocks combine a low weight with a hard outer layer and a practical stacking system. This allows you to build the pool walls quickly and systematically, while the polystyrene helps reduce heat loss through the walls.
Whether you do the work yourself or work with a pool builder, this construction system provides a practical foundation for a custom-made pool. During construction, the blocks are fitted with steel reinforcement and then filled with concrete. This creates a reinforced concrete structure with a permanent, insulating formwork.
Easy to stack and quick to build
The construction system uses stackable blocks made of expanded polystyrene, also known as EPS or Styrofoam. The principle is similar to building blocks: you place the blocks layer by layer to build the desired pool wall. Thanks to the 100 cm length, you can make quick progress. For a wall height of 1.50 meters, five layers of 30 cm are required.
The low weight makes the blocks easy to move and handle. This is convenient when setting out and building the walls and makes the system attractive to DIY builders. A level foundation, accurate measurements, and correct placement form the basis for a good result.
High density for a sturdy wall surface
These high-density pool blocks have a PS60/30 construction. The core consists of polystyrene with a density of 30 kg/m³ and is fitted with a hard outer layer with a density of 60 kg/m³. This outer layer makes the surface more resistant to dents, scratches, and deformation during processing.
Thus, the block combines the ease of use of lightweight polystyrene with a sturdy surface. The hard outer layer helps keep the wall neat during construction and in preparation for the final pool lining.
Concrete and reinforcement provide structural strength
The polystyrene blocks form the formwork for the pool wall. During construction, the required steel reinforcement is installed, after which the hollow spaces are filled with concrete. The blocks remain in place after filling and form an insulating layer around the concrete core.
The final strength is determined by the entire structure: the subsoil, floor slab, reinforcement, and concrete fill must be coordinated. The dimensions of the pool and any steps or tanning ledges also play a role. The walls are filled according to the system's processing instructions.
Insulating properties for heat retention
Polystyrene helps limit heat transfer between the pool water and the surrounding soil. As a result, the blocks help retain heat. In a heated pool, this can reduce the energy required to keep the water at the desired temperature.
The total energy savings depend on the entire pool construction and its use. In addition to wall insulation, floor insulation, a good pool cover, the outside temperature, and the desired water temperature also have an impact. These pool blocks thus provide a practical foundation for a well-insulated pool.
Flexible in shape and layout
With the blocks and suitable accessories, you can realize various pool designs. In addition to straight walls, entry steps and tanning ledges are also possible, provided they are properly designed structurally. This allows you to tailor the pool to the available space and your preferences for comfort and use.
When designing, also take into account the placement of lighting, return jets, and other wall penetrations. These built-in components are installed during the construction phase so that they are incorporated into the pool wall in the correct position.
Step-by-step installation
Construction begins with excavating and preparing the construction pit. The floor reinforcement is then installed, and the concrete floor slab is poured and finished to the desired height. This floor slab forms the foundation for the pool walls.
The first row of blocks is accurately placed on the prepared floor slab, as prescribed, in a mortar bed. The remaining layers, steel reinforcement, and built-in components follow. The blocks are connected or bonded according to the system's instructions.
Once the walls are fully built and inspected, they are filled with concrete. This is followed by preparation for a suitable waterproof pool lining. The blocks and the concrete core form the wall structure; the pool lining provides the waterproof finish.
How many blocks and how much concrete do you need?
The required quantity depends on the pool size, wall height, corner connections, and any additional elements. For an 8 x 4 x 1.50-meter pool, according to the specified calculation method, you will need approximately 100 blocks and about 4.3 m³ of concrete for the walls.
This calculation assumes five layers and a calculated perimeter of 25 meters, including a 1-meter allowance. The indicative concrete consumption is 115 liters per square meter of pool wall. Concrete for the floor slab and additional material for steps or tanning ledges are not included.
Order at least 1 to 2 extra blocks for limited cutting waste or potential damage. For a design with many corners or custom dimensions, a larger reserve may be required.
Turn your patio or garden into a place to relax together with the Market Twin Sterling Marble Spa. This 2-seater spa has two seating positions and 46 massage jets, powered by a 3 hp massage pump with two speeds. The compact size of 200 x 135 x 80 cm offers room for a comprehensive wellness experience without having to install a large spa.
The Sterling Marble acrylic shell is combined with grey side panels with a wood texture. Interior lighting, illuminated exterior corners, three fountains and a waterfall create an atmosphere. Via the Bluetooth audio system, you can listen to your own music while relaxing.
Two seating positions with 46 massage jets
The two seating positions each offer their own massage layout. The first position has 19 jets for the neck, shoulders, upper back, lower back, thighs and calves. The second seating position has 27 jets, with extra attention to the broad back muscles.
Two headrests support a comfortable lying position. The massage pump with two speeds offers different operating modes. By switching seating positions, you can discover which jet layout best suits your preference.
Atmospheric lighting and moving water
The LED lighting on the inside and on the exterior corners gives the spa a neat appearance even in the evening. Three fountains with LED lighting and an illuminated waterfall add moving water to the experience.
The built-in Bluetooth audio system with a speaker makes it possible to play music from a suitable device. This way, you combine hydromassage, lighting and music during your relaxation moment.
Heating and insulating cover
The spa has a 2 kW heater to heat the water and keep it at temperature. An insulated base with PVC and the standard included 12 cm thermal cover help to limit heat loss.
Close the cover when you are not using the spa. This helps retain heat and keeps dirt out. The warm-up time and energy consumption depend on several factors, including the outside temperature, the starting temperature of the water and usage.
Filtration and UV water treatment
The Market Twin Sterling Marble Spa is equipped with one filter cartridge and a UV lamp. The filter catches dirt particles; the UV lamp supports the water treatment.
For clean spa water, regular monitoring of water values, appropriate disinfection and cleaning of the filter are still required. The UV lamp does not replace this maintenance.
Aristech acrylic and a stainless steel frame
The shell is made of Aristech acrylic in the Sterling Marble version. The stainless steel frame supports the construction. The grey, UV-resistant side panels have a wood texture and combine a natural appearance with a calm color.
Operation is via a Gecko Inc. panel. This makes the available spa functions accessible from the edge.
Plug & Play at 230 V
The spa is designed as a Plug & Play model for a standard 230 V socket, according to the specified connection data. Have the connection and protection checked beforehand to ensure they meet the installation regulations.
The net weight is 280 kg and the water capacity is 530 liters. Filled, the spa therefore weighs approximately 810 kg, excluding users. Ensure a flat, load-bearing surface and sufficient space for access and maintenance. Delivery and placement depend on the accessibility of the location.
Enjoy a hydro massage together, with atmospheric lighting and your favorite music in the Market Twin Odyssey Spa. This 2-seater spa has two seating positions with a total of 46 massage jets. Measuring 200 x 135 x 80 cm, the Twin offers a comprehensive wellness experience in a compact size.
The Odyssey finish gives the acrylic tub a distinctive look. Grey side panels with a wood texture and LED lighting on the outer corners complete the look. Thanks to the Plug & Play design, the spa operates on 230 V, without the need for a high-voltage connection.
Two seating positions, each with its own massage experience
The Market Twin Odyssey Spa has two seating positions with different jet layouts. The first seating position has 19 jets for the neck, shoulders, upper back, lower back, thighs, and calves. The second seating position is equipped with 27 jets, with extra attention to the broad back muscles.
Two headrests support your head while you relax. The 3 hp massage pump has two speeds and powers the hydro massage. By switching places, you can experience which massage layout best suits your preference.
Illuminated fountains and waterfall
The LED lighting on the inside and on the outer corners creates an atmosphere as soon as it gets dark. Three illuminated fountains and a waterfall with LED lighting add moving water to the experience.
Via the built-in Bluetooth audio system with a speaker, you can play music from a compatible device. This allows you to combine the massage with a relaxing playlist or your favorite songs.
Heating and thermal cover
The built-in 2 kW heater brings the water up to temperature and keeps it warm. The insulated base and the standard 12 cm thermal cover help reduce heat loss.
By closing the cover after use, the accumulated heat is better retained and less dirt enters the water. The warm-up time and power consumption depend on several factors, including the outside temperature, the desired water temperature, and how often you use the spa.
Filtration and UV support
The spa is equipped with one filter cartridge and a UV lamp. The filter captures dirt particles and the UV lamp supports the water treatment.
For clean and pleasant spa water, regular monitoring of the water values, proper disinfection, and filter cleaning are still required. The UV lamp complements this maintenance.
Aristech acrylic and a stainless steel frame
The tub is made of Aristech acrylic in the Odyssey color. The stainless steel frame supports the structure. The grey side panels are UV-resistant and have a wood texture that blends beautifully with various garden and patio styles.
With the Gecko Inc control panel, you can control the available spa functions from the edge. This keeps the controls within easy reach.
Compact spa with 230 V connection
With a width of 135 cm, the Market Twin Odyssey Spa is ideal for spaces where a larger spa would not fit as well. However, leave enough space around it for getting in and out, maintenance, and handling the cover.
The spa has a net weight of 280 kg and a water capacity of 530 liters. When filled, the weight is approximately 810 kg, excluding users. A flat, load-bearing surface is therefore essential.
The Plug & Play connection is intended for 230 V. Before installation, check that the socket, electrical circuit, and protection meet the installation regulations. Delivery and installation options depend on access to your location.
Turn your patio or garden into a place to relax together with the Market Twin Sterling Marble Spa. This 2-seater spa has two seating positions and 46 massage jets, powered by a 3 hp massage pump with two speeds. The compact size of 200 x 135 x 80 cm offers room for a comprehensive wellness experience without having to install a large spa.
The Sterling Marble acrylic shell is combined with grey side panels with a wood texture. Interior lighting, illuminated exterior corners, three fountains and a waterfall create an atmosphere. Via the Bluetooth audio system, you can listen to your own music while relaxing.
Two seating positions with 46 massage jets
The two seating positions each offer their own massage layout. The first seat has 19 jets for the neck, shoulders, upper back, lower back, thighs and calves. The second seating position has 27 jets, with extra attention to the broad back muscles.
Two headrests support a comfortable lying position. The massage pump with two speeds offers different operating modes. By switching seating positions, you can discover which jet layout best suits your preference.
Atmospheric lighting and moving water
The LED lighting on the inside and on the exterior corners gives the spa a neat appearance even in the evening. Three fountains with LED lighting and an illuminated waterfall add moving water to the experience.
The built-in Bluetooth audio system with a speaker makes it possible to play music from a suitable device. This way, you combine hydromassage, lighting and music during your relaxation moment.
Heating and insulating cover
The spa has a 2 kW heater to bring the water to temperature and keep it there. An insulated PVC floor and the standard 12 cm thermal cover included help to limit heat loss.
Close the cover when you are not using the spa. This helps retain heat and keeps dirt out. The warm-up time and energy consumption depend on several factors, including the outside temperature, the starting temperature of the water and usage.
Filtration and UV water treatment
The Market Twin Sterling Marble Spa is equipped with one filter cartridge and a UV lamp. The filter catches dirt particles; the UV lamp supports the water treatment.
For clean spa water, regular checking of the water values, appropriate disinfection and cleaning of the filter are still required. The UV lamp does not replace this maintenance.
Aristech acrylic and a stainless steel frame
The shell is made of Aristech acrylic in the Sterling Marble version. The stainless steel frame supports the construction. The grey, UV-resistant side panels have a wood texture and combine a natural appearance with a calm color.
Operation is via a Gecko Inc. panel. This makes the available spa functions accessible from the edge.
Plug & Play at 230 V
The spa is designed as a Plug & Play model for a standard 230 V socket, according to the specified connection data. Check beforehand that the connection and protection meet the installation regulations.
The net weight is 280 kg and the water capacity is 530 liters. Filled, the spa therefore weighs approximately 810 kg, excluding users. Ensure a flat, load-bearing surface and sufficient space for access and maintenance. Delivery and placement depend on the accessibility of the location.
Finish your swimming pool with the beige AstralPool NORM skimmer. This version has a capacity of 17.5 liters and a wide XXL opening of 495 x 80 mm. The skimmer draws surface water with floating debris into the filtration system, thereby supporting daily water circulation.
The beige color combines beautifully with sand-colored pool liners, warm tile shades, and natural stone pool edges. The housing is made of UV-resistant ABS and is intended for use in pools with liners, panels, or a suitable prefab construction.
Wide opening for a clean water surface
Leaves, insects, and other floating debris are drawn into the XXL opening along with the surface water. Proper placement relative to the return inlets helps direct this debris toward the skimmer.
The recommended flow rate for the NORM version described is 7.5 m³ per hour. Coordinate the number of skimmers, pump capacity, and piping with the size and layout of the pool. The 17.5-liter capacity refers to the skimmer housing, not the suitable pool volume.
Beige finish and UV-resistant ABS
The beige version gives the skimmer a subtle appearance in a pool with warm or natural colors. By also choosing matching return inlets and other built-in components, a cohesive finish is created.
The UV-resistant ABS is designed to withstand exposure to sunlight. Regular cleaning is still necessary to keep the skimmer clean and maintain good flow.
Reinforced connection
The NORM version described above features a brass insert that reinforces the threaded connection. This helps limit wear at the connection. When ordering, check that the beige variant has the same connection design.
Use suitable fittings and sealing materials during installation. Even with a reinforced connection, careful screwing in is important to prevent damage and leakage.
Accessible installation and suitable installation height
The adjustable skimmer lid helps match the top to the surrounding finish. Keep the lid accessible so that collected debris can be easily removed.
Within the range, a standard version and a shortened version for a higher water level are mentioned. Check which variant you are ordering and whether it fits the wall construction and the desired water level.
Keep your pool surface clean with the AstralPool NORM skimmer. This grey version has a capacity of 17.5 litres and a wide XXL opening measuring 495 x 80 mm. Surface water with floating debris is drawn through this opening to the filtration system.
The skimmer is designed for liner, panel, or suitable precast pools. The UV-resistant ABS is suitable for prolonged exposure to sunlight. The grey finish combines well with grey pool liners and matching in-wall fittings.
Wide opening for surface drainage
The XXL opening allows water to flow into the skimmer over a generous width. This carries away leaves, insects and other floating debris before they sink to the bottom.
The recommended flow rate is 7.5 m³ per hour. Size the pump, piping and number of skimmers accordingly. The 17.5-litre capacity refers to the skimmer housing and is not an indication of the suitable pool volume.
UV-resistant ABS with a grey finish
The housing is made of UV-resistant ABS. This material helps make the skimmer resistant to exposure to sunlight. The grey colour provides a cohesive look when using grey return fittings, light rings or other visible components.
According to the product information provided, the skimmer complies with EN 13451-3. Correct installation in accordance with the installation instructions remains important.
Reinforced connection with brass insert
This version features a brass insert in the connection. This reinforces the threaded connection and makes it more resistant to wear during installation.
Even with a metal insert, careful screwing in is necessary. Use suitable fittings and an appropriate seal to prevent damage and leakage.
Adjustable cover and skimmer flap
The skimmer has an adjustable cover and a skimmer flap. The flap supports the flow of surface water; the adjustable cover helps align the top with the surrounding finish.
The specified distance between the suction fitting and the skimmer cover is 80 to 125 mm. Take this dimension into account during installation and ensure that the cover remains accessible for removing collected debris.
Choose the right version
Within the range, a standard version and a shortened version for a higher water level are mentioned. Both have a slope of 6° according to the product information.
Which version belongs with item 56176CL129 is not specified separately. Check this before installation to ensure that the skimmer matches the wall construction and the desired water level.
Heat your pool with the AquaForte Mr. Silence 30+ R290 12 kW. This pool heat pump combines InverPad® Turbo technology with R290 refrigerant. The inverter control adjusts the operation to the heat demand, aiming for a comfortable water temperature and low energy consumption.
The Mr. Silence 30+ series was developed with a focus on noise reduction and efficiency. This version has a rated heating capacity of 12 kW. The actual heat output and efficiency depend on factors including the outdoor temperature, water temperature, and the load on the heat pump.
InverPad Turbo for tailored heat output
Inverter technology adjusts the heat pump's operation to the required heat. More capacity is needed when heating the pool than when maintaining the water temperature. By adjusting the power accordingly, the system can operate more quietly and efficiently.
For optimal results, the heat pump must be suitable for the pool volume, insulation, and intended period of use. A pool cover helps retain the accumulated heat and reduces the heat demand.
High efficiency with a COP of up to 30
The Mr. Silence 30+ series has a rated COP of up to 30. COP describes the ratio between heat output and electricity consumed: at a COP of 30, thirty times as much heat is output as electrical energy consumed under the relevant test conditions.
This maximum efficiency does not apply under all conditions. It also does not mean that this 12 kW version provides 30 kW of heating capacity. In colder weather or when a higher water temperature is desired, the efficiency may be lower.
Designed for quiet operation
The design focuses on reducing mechanical noise, airflow noise, and vibrations. The provided series description states a noise level of 36.4 dB(A).
The measurement distance and operating conditions are not specified. The audible noise level at your location also depends on the placement, the distance to the patio, and any reflection off walls. Therefore, choose a location with sufficient free air circulation in accordance with the installation instructions.
R290 as refrigerant
This version uses R290 as refrigerant. R290 has a low global warming potential and is therefore an important part of the design of this generation of heat pumps.
The total environmental impact also depends on the electricity consumption and the lifespan of the system. Proper sizing and careful use therefore remain important.
Developed for a longer swimming season
The Mr. Silence 30+ is presented as a heat pump for use throughout the four seasons. Whether your pool can also maintain the desired temperature in winter depends on the climate, heat losses, and available heating capacity at low outdoor temperatures.
For year-round use, performance under winter conditions is decisive. Therefore, tailor your choice to the desired water temperature, pool size, and cover.
Give your pool lighting a neat finish with this light grey Duravision front ring. The ring frames the lamp on the pool side and coordinates the visible finish with the colour of the pool wall and other built-in components.
This version is intended for models PLA100, PLP100 and DVS100 from the Vision Adagio Pro, Vision Pro and Vision Spectra series. This allows you to use the same light grey finish with these suitable models.
Light grey finish around the lamp
The light grey colour combines beautifully with grey pool lining and matching components, such as return inlets and skimmers. The front ring provides a neat frame for the lighting without changing the colour of the light.
You can also use this to change the appearance of the lamp when replacing an existing front ring. Please bear in mind that there may be colour differences between new and existing components.
Suitable for multiple Vision series
The front ring is suitable for the 100 versions of Vision Spectra, Vision Adagio Pro and Vision Pro mentioned. Before ordering, check the model designation of your lamp: compatibility with multiple series does not mean that the ring fits all lamp sizes.
Install the ring according to the instructions for the relevant lamp. This product is the front ring; the pool lamp itself is not included in this product description.
Set the mood of your pool with the SpectraVision DVS100-TW. This LED pool light from Duravision offers adjustable white light, allowing you to choose between a cooler and a warmer appearance. With a power of 20 W and a stated light output of 1500 lumens, you illuminate the pool in the desired shade of white.
The lamp operates on 12 V AC and has a two-wire connection. The resin-filled NoAir™ housing, the detachable 2-meter cable and the practical mounting systems make this version suitable for a neat installation. The lamp is also suitable for pools with salt electrolysis.
From cool white to warm white
The TW designation stands for adjustable white light. This allows you to change the color temperature of the lighting: choose a cooler shade of white for a bright appearance or warmer white for a softer evening atmosphere.
Adjustable white is different from colored RGB lighting. This version offers different shades of white. What control is required for this must be coordinated with the instructions for the DVS100-TW. A dimming function is not confirmed in the provided product information.
Resin-filled NoAir™ housing
The lamp is equipped with a resin-filled NoAir™ housing. This construction is intended to prevent water infiltration and condensation formation in the lamp.
The version is suitable for use in pools with salt electrolysis. During use and maintenance, adhere to the prescribed water values and installation conditions.
Practical installation in a suitable wall fitting
The Vision Spectra lights are designed for installation in most 1½″ wall fittings. Check beforehand whether the fitting and mounting components used are suitable for this version.
QuickConnect™, PressFit™ and ClickOn™ support the connection, placement and finishing of the lamp. With a suitable Vision front ring, you coordinate the visible finish with the pool wall and the other built-in parts. The front rings can be mounted with the separately available SG101 tool set.
Detachable 2-meter cable
The lamp is equipped with a detachable 2-meter cable. Coordinate the further cabling with the distance to the power supply and the electrical load. The manual indicates what cable cross-section is required.
For the power supply, a suitable 12 V AC transformer is required. In addition, check which control is suitable for setting the shade of white. The scope of delivery of a transformer, control and front ring is not listed.
Coordinating the lighting with your pool
The required number of lamps depends on the dimensions, shape and lining of the pool. The placement also determines how the light spreads through the water.
Therefore, include the lamps in the pool design. This allows you to prepare the wall fittings and cable routes in advance at the desired positions.
The AstralPool Unik skimmer mouth in grey neatly finishes the opening of a suitable Unik skimmer. This part forms the visible finish around the skimmer opening on the pool side and has item number 74839CL129.
The grey version combines beautifully with grey pool lining and matching built-in parts, such as return inlets and vacuum connections. This way, you can match the appearance of the skimmer to the rest of the pool.
Finish of the skimmer opening
Surface water flows through the skimmer opening into the skimmer and the connected filter system. The skimmer mouth forms the finish of this opening. It is a separate part and not a complete skimmer.
This version belongs to the AstralPool Unik series. Before ordering, check whether the item fits your specific skimmer model. The exact compatible models and dimensions are not listed in the provided product information.
Grey version for a cohesive look
With a grey skimmer mouth, you can match the visible parts in the pool wall. The color matches a pool with grey accents and can also be used to replace the finish of an existing, suitable skimmer.
When replacing, take into account any color differences due to the aging of existing parts or differences between materials.
The grey AstralPool Unik skimmer cover gives a suitable Unik skimmer a neat finish. The cover is intended as a cover component and has item number 74838CL129.
The grey colour combines nicely with other grey pool components. This allows you to match the finish of the skimmer with the appearance of your pool and the surrounding materials.
Finish for a suitable Unik skimmer
This cover belongs to the AstralPool Unik series. Before ordering, check whether item 74838CL129 is suitable for your skimmer model. The exact compatible skimmer models are not listed in the provided product data.
The cover is a separate cover component and not a complete skimmer. When replacing it, it is therefore important to compare both the model and the mounting of the existing component.
Grey version
The grey finish offers an alternative to a white or darker cover. By combining the colour with matching built-in components, a cohesive look is created around the pool. Please note that shades of grey may vary between different products and materials.
The AstralPool Unik skimmer draws surface water from your pool and sends it to the filtration system. Floating debris, such as leaves and insects, is removed in the process. This helps the skimmer keep the water surface clean and supports water circulation.
This model is designed for concrete pools and has item number 74830. The skimmer is built into the pool wall and connected to the suction line of the filtration system.
Removal of surface water and floating debris
Debris often enters the pool via the water surface. By removing the top layer of water, the skimmer helps remove this debris before it sinks to the bottom.
Proper operation depends on the placement of the skimmer, the water level, and the flow from the return jets. Coordinate these elements so that surface debris is directed toward the skimmer.
Installation in a concrete pool wall
Take the position of the Unik skimmer into account when designing the pool. The installation height must match the intended water level and wall finish.
Before installation, check the installation dimensions, pipe connections, and required sealing materials. Ensure the skimmer remains accessible for inspection and the removal of collected debris.
Coordination with the filtration system
The required number of skimmers depends on the size and shape of the pool, the desired flow rate, and the distribution of the suction points. The recommended flow rate for item 74830 is not stated in the provided information.
Therefore, check the technical specifications before combining the skimmer with a pump and piping. Proper sizing helps the system function correctly.
With the AstralPool vacuum connection, you create a fixed connection point for a pool vacuum in the concrete pool wall. Using a suitable hose connection, you connect the vacuum to the suction line of the pool system. This allows you to remove loose debris from the bottom and direct it to the connected filtration system.
This grey version is made of ABS and features 2″ male thread and a 50 mm internal solvent-weld connection. For installation, the wall fittings with item number 15658 or 15659 are recommended.
Fixed connection point for pool cleaning
A vacuum connection in the wall provides a practical place to connect a manual pool vacuum. The connection forms the link between the vacuum hose and the underlying suction line.
The required suction power is provided by the connected system. Its performance depends on factors including the pump, the pipework configuration, and the position of the valves. Also check which hose adapter is required; the specified connection dimensions do not guarantee that every vacuum hose will fit directly.
Two connection options
The connection has 2″ male thread and can therefore be installed using a suitable female-threaded fitting. It also features a 50 mm internal solvent-weld connection.
Coordinate the installation with the wall fitting and pipework being used. Use suitable connecting and sealing materials, and check the connections for water tightness before the pool wall is permanently finished.
Installation with a suitable wall fitting
For this vacuum connection, the AstralPool wall fittings 15658 and 15659 are recommended. These provide the passage through the pool wall to the underlying pipework.
Determine the position of the connection during the preparation of the pool construction. Check that the chosen wall fitting is suitable for the wall thickness and the final finish. Also follow the product instructions for closing off the connection point when it is not in use.
Grey finish for a cohesive look
The grey ABS version combines well with grey pool lining and other grey built-in components, such as return inlets and skimmers. This gives the connection point a discreet appearance in the pool wall.
The AstralPool Multiflow return jet returns filtered water to the pool. This grey return jet forms the visible connection point of the return line in the pool wall and supports water circulation.
The return jet is made of ABS and features a 2″ male thread and a 50 mm internal glue connection. For installation, the wall fittings with item number 15658 or 15659 are recommended. The grey finish combines beautifully with grey pool lining and matching in-wall components.
Return of filtered pool water
After filtration, the water flows back into the pool via the return line and the return jet. A well-positioned return jet helps distribute this water throughout the pool.
The final circulation depends on the number of return jets, their position, the pump capacity, and the location of the skimmers or other drainage points. Therefore, take the distribution of the return jets into account when designing the pool installation.
Two connection options
The Multiflow return jet has a 2″ male thread for mounting in a suitable female-threaded connection. In addition, it features a 50 mm internal glue connection.
Which connection you use depends on the chosen wall construction and piping. Use suitable connection and sealing materials and follow the installation instructions for a watertight installation.
To be combined with wall fitting 15658 or 15659
For this return jet, wall fittings 15658 and 15659 are recommended. A suitable wall fitting creates the connection between the return jet on the pool side and the return line behind it.
When choosing the wall fitting, check that the length and design suit the pool wall and the finish. Determine the position before permanently finishing the wall.
Grey ABS design
The ABS housing is grey. This allows you to match the return jet to the color of the pool lining, skimmers, and other visible components. This gives the pool wall a cohesive finish.
The Duravision PZA-WC-NG wall fitting forms the basis for installing DURAVISION LED pool lighting. According to the product information, this universal wall fitting is suitable for all types of swimming pools, with or without a liner, and is compatible with all DURAVISION LED lights.
The wall fitting combines an integrated cable gland with space for up to 1.5 metres of cable. This makes it possible to store extra cable length behind the light and bring the light above the water surface for maintenance, provided that the installation and available cable length allow this.
Installation without silicone sealant
The design allows installation without silicone sealant. Using the sealing components designed for this purpose, you can achieve a watertight connection in accordance with the installation instructions.
The integrated cable gland seals the cable entry and helps prevent pool water from entering the flexible hose or pipe behind it. Correct installation remains essential for a reliable seal.
Storage space for up to 1.5 metres of cable
The wall fitting can store up to 1.5 metres of cable. This cable length provides freedom of movement when the light is removed from the fitting for maintenance.
By reserving sufficient cable in advance, the light can be more easily brought above the water surface. Take into account the installation depth and the distance to the pool edge.
Flexible cable routing
The conical connections guide the cable during installation. This facilitates installation and helps limit damage caused by the cable snagging.
Together with the integrated cable gland, this ensures a clear cable route between the light and the pipe behind it.
Extendable for different wall thicknesses
The PZA-WC-NG has an installation length of 269 mm and a 50 mm pipe connection. For a greater wall thickness, the system can be extended with a suitable 50 mm pipe and sleeve.
This extension option makes it easier to adapt the wall fitting to the pool construction. Determine the required length in advance and take into account the wall finish and the space available for the connections.
The Spectravision toolset simplifies the installation of the front ring and cable feed-through of a suitable wall fitting. The set supports the installation work on the pool lighting and helps to guide the cable through the fitting.
The cable puller makes guiding the cable easier. This makes this toolset a practical aid in preparing and installing a suitable Spectravision installation.
Assistance with installing the front ring and cable feed-through
The toolset is intended to make the front ring and cable feed-through easier to install. Use the tools according to the installation manual of the set and the corresponding wall fitting.
Check beforehand whether the toolset is suitable for your version. The exact compatible models are not listed in the provided description.
Easier cable guiding
With the cable puller, you guide the cable through the designated opening. This is useful when the cable cannot easily be fed through the fitting by hand.
Careful cable guiding helps with connecting the lighting. During installation, prevent the cable from kinking or being damaged and follow the prescribed procedure.
With the Cepex AstralPool wall sleeve, you create a connection through a concrete pool wall for suitable Multiflow inlets and suction connections. The sleeve is made of ABS and has a standard length of 300 mm. If necessary, you can shorten it to 250 or 175 mm, allowing you to adjust the length to the wall construction.
The version features a 2″ female thread connection and a pipe connection with the specified size of 50/63 mm. This makes the wall sleeve the connection between the recessed part on the pool side and the piping behind it.
Adjustable length for different wall thicknesses
The option to shorten the wall sleeve offers flexibility during installation. Depending on the construction, you use the full length of 300 mm or shorten the sleeve to 250 or 175 mm according to the product instructions.
Determine the required length before modifying the component. Take into account the concrete wall, the finish, and the space for the connections. This prevents the sleeve from proving too short after shortening.
For Multiflow inlets and suction connections
This wall sleeve is intended for suitable Multiflow inlets and suction connections. With an inlet, it forms the passage for the water flowing back into the pool. With a suction connection, it connects the connection point to the corresponding suction pipe.
The function is therefore determined by the connected component and the piping route. Check beforehand whether the chosen inlet or suction connection matches the thread and design of the wall sleeve.
Installation in a concrete pool wall
Take the position of the wall sleeve into account during the preparation of the pool construction. Correct placement and alignment make connecting the piping and finishing the wall easier.
The ABS sleeve remains part of the wall construction. Check the connections for watertightness before the installation is permanently finished, as the connections are less easily accessible after installation.
With the PL-REM-200 transformer, including remote control, you can power and control compatible pool lighting from a single system. The set consists of a base station with a built-in transformer and a wireless remote control. This allows you to switch compatible SPECTRAVISION lighting on and off and operate the color-changing function of suitable lamps.
According to the product information, the wireless range is up to 200 meters. This allows you to control the lighting from the patio or another location around the pool. The base station has a maximum switching capacity of 200 VA and, thanks to its IP54 enclosure, is suitable for outdoor installation in accordance with the installation instructions.
Transformer and wireless control in one set
The combination of a transformer and a wirelessly controlled base station brings together the power supply and control of suitable pool lights. With the included remote control, you do not need to go to the technical room to adjust the lighting.
According to the provided information, the set can be used with Adagio PLA, Moonlight, and Vision Spectra for switching on/off and changing colors. Check beforehand whether your specific lamp model is suitable for this transformer and control system.
Control from up to 200 meters away
The remote control has a specified range of up to 200 meters. The actual range depends on the environment: walls, obstacles, and the placement of the base station can affect reception.
Choose an installation location where the base station can be connected in accordance with the instructions and the wireless signal is received properly.
Also suitable for switching other devices
In addition to suitable pool lighting, the PL-REM-200 can also control other suitable devices. Check the electrical characteristics of the device and the permitted load of the relevant output beforehand.
The maximum switching capacity is 200 VA. This value is not equal to 200 watts for every device. Therefore, match the connected equipment to the product specifications and wiring diagram.
Suitable for outdoor installation
The base station has an IP54 enclosure and, according to the product information, can be installed outdoors. Install it according to the installation instructions and ensure that cable entries and connections are carried out correctly. The enclosure is not intended for immersion.
Choose the right version for dimmable lighting
This version offers on/off control and color changing for compatible lamps. For dimmable lighting, the product information specifies the SG145 PLP-REM350. Choose that version if you also want to control the light intensity.
With the AstralPool type D control box, you can control the daily switching times of the pool pump and power suitable underwater lighting from a single enclosure. This version combines an adjustable motor protection device of 6 to 10 amperes with a 24-hour programmable timer and a built-in 630 W transformer with an output voltage of 12 V.
The control box has three operating modes: Auto, 0 and Manual. This allows you to operate the pump automatically according to a program, switch off the operation, or choose manual operation. The protected output also offers connection options for two suitable underwater lights.
Automatic filtration with a 24-hour timer
With the programmable timer, you set the daily operating times of the pool pump. In automatic mode, the pump follows the set program. This ensures that filtration takes place at fixed times without having to switch the pump on and off yourself each time.
If you want to temporarily deviate from the program, use the manual mode. The zero mode switches off the operation. A separate timer program for the lighting is not mentioned in the product information.
Motor protection for pumps from 6 to 10 A
Type D has the highest setting range within the shown overview of types A through D. The motor protection device is adjustable from 6 to 10 A and must be matched to the rated current of the connected pump motor.
According to the provided data, type D is suitable for a pump power of 1.5 HP at single-phase 230 V and 2 to 3 HP at three-phase 230 V. For the specified 400 V connection, 4 HP is listed. Always check the motor current on the nameplate and the official wiring diagram. The power in HP alone is insufficient to select the correct control box.
Comparison of AstralPool types A through D
The versions differ in the setting range of the motor protection device. Choose the range that matches the pump and the electrical installation.
SKU in overview
Type
Motor protection setting range
Pump power 1-phase 230 V
Pump power 400 V*
Pump power 3-phase 230 V
74991
A
1.6–2.5 A
¼ HP
¾–1 HP
½ HP
74992
B
2.5–4 A
½ HP
1.5–2 HP
¾–1 HP
74993
C
4–6.3 A
¾–1 HP
3 HP
1.5 HP
74994
D
6–10 A
1.5 HP
4 HP
2–3 HP
Built-in transformer for underwater lighting
The built-in transformer provides 12 V and has a rated power of 630 W. The protected output is intended for two suitable underwater lights.
Match the total connected lamp power, cable length, and cable cross-section to the transformer and the installation regulations. Also check whether the lights are suitable for the type of output voltage. A suitable wattage alone does not confirm electrical compatibility.
Pump control and light power supply in one enclosure
The control box neatly combines the programmable timer, motor protection device, and lighting transformer. This makes the enclosure a central part of the technical pool installation.
Choose the installation location according to the installation regulations and keep the enclosure accessible for operation and maintenance. The protection class and dimensions are not specified and must be checked before installation.
With the AstralPool type B control box, you can set the daily operating times of the pool pump and access a power supply for suitable underwater lighting. The enclosure combines an adjustable motor protection device with a range of 2.5 to 4 amps, a 24-hour programmable clock, and a built-in 630 W transformer with an output voltage of 12 V.
With the Auto, 0, and Manual settings, you can easily choose between automatic operation, switching off, and manual operation. The control box is also equipped with a protected output for two underwater lights. This keeps the pump control and lighting power supply conveniently together.
Automatic filtration at set times
The 24-hour programmable clock allows you to set the daily operating times of the pool pump. In automatic mode, the pump follows this program. This allows you to coordinate filtration times with the use and needs of the pool.
Use the manual setting for temporary deviations. The zero setting switches off the operation. A separate lighting schedule is not mentioned in the product information.
Motor protection from 2.5 to 4 amps
The type B version is intended for a suitable pump motor with a rated current within the adjustable range of 2.5 to 4 A. The motor protection must be set according to the specifications of the connected pump.
According to the provided overview, type B is suitable for a pump power of ½ HP at 1-phase 230 V and ¾ to 1 HP at 3-phase 230 V. For the specified 400 V connection, 1.5 to 2 HP is listed. Always check the motor current and connection method using the nameplate and the official wiring diagram.
Comparison of AstralPool types A through D
Type B has a higher adjustable range than type A and a lower range than types C and D. Choose the version that matches the rated motor current of the pump.
SKU in overview
Type
Motor protection adjustable range
Pump power 1-phase 230 V
Pump power 400 V*
Pump power 3-phase 230 V
74991
A
1.6–2.5 A
¼ HP
¾–1 HP
½ HP
74992
B
2.5–4 A
½ HP
1.5–2 HP
¾–1 HP
74993
C
4–6.3 A
¾–1 HP
3 HP
1.5 HP
74994
D
6–10 A
1.5 HP
4 HP
2–3 HP
Built-in transformer for underwater lights
The transformer provides 12 V and has a rated power of 630 W. The protected output is intended for two suitable underwater lights.
Coordinate the total lamp power and wiring with the transformer. Also check that the electrical characteristics of the lights match the output. The type B version has the same rated transformer capacity as the previously described types A and C.
Central control in the technical room
The combination of motor protection, clock, and transformer makes this control box a practical component of the pool installation. The most important pump control functions are available in one place.
Install the enclosure according to the installation instructions and leave sufficient space for connection, operation, and maintenance. Check the protection class before determining the installation location.
With the AstralPool control box type A, you control the daily switching times of the pool pump and power suitable underwater lighting from a single enclosure. This version combines an adjustable motor protection from 1.6 to 2.5 amperes with a 24-hour programmable clock and a built-in 630 W transformer with an output voltage of 12 V.
The control box features three operating modes: Auto, 0 and Manual. In addition, there is a protected output for two underwater lights. This allows you to neatly combine the pump control and light power supply in the technical installation of your pool.
Automatic filtration with a 24-hour clock
With the programmable clock, you set the times when the pool pump should operate. In automatic mode, the pump follows the set daily program. This allows filtration to take place at fixed times.
If you want to temporarily deviate from the program, use the manual mode. The zero setting switches off the operation. A separate programming function for the underwater lighting is not listed.
Motor protection for a lower current range
Type A has an adjustable motor protection from 1.6 to 2.5 A. This version is therefore intended for pump motors whose rated current falls within this range. The protection must be set to the connected motor.
According to the provided data, type A is suitable for a pump power of ¼ HP at 1-phase 230 V, ¾ to 1 HP at 3-phase 400 V, or ½ HP at 3-phase 230 V. Always check the motor current on the nameplate and the official wiring diagram. The power in HP alone does not determine whether the combination is suitable.
Comparison with types B, C and D
The main difference between the versions is the adjustment range of the motor protection. Type A has the lowest range; versions B, C and D are intended for higher motor currents.
Type
Motor protection adjustment range
Pump power 1-phase 230 V
Pump power 400 V*
Pump power 3-phase 230 V
A
1.6–2.5 A
¼ HP
¾–1 HP
½ HP
B
2.5–4 A
½ HP
1.5–2 HP
¾–1 HP
C
4–6.3 A
¾–1 HP
3 HP
1.5 HP
D
6–10 A
1.5 HP
4 HP
2–3 HP
Built-in transformer for two underwater lights
The control box is equipped with a 630 W transformer with an output voltage of 12 V. Two suitable underwater lights can be connected via the protected output.
Match the lights, the total connected power, and the cabling to the transformer. The transformer capacity is independent of the adjustment range of the motor protection: type A therefore has the same specified lighting power supply as the previously described type C.
Organized control in a single enclosure
By bringing together the programmable clock, motor protection, and transformer, the control box provides a central control point for the connected pump and a power supply for the pool lighting. Choose a suitable mounting location according to the installation instructions and keep the enclosure accessible for operation and maintenance.
With the AstralPool control box type C, you can control the switching times of the pool pump and have a power supply for suitable underwater lighting. This control box combines an adjustable motor protection device, a 24-hour programmable timer and a built-in 630 W transformer with an output voltage of 12 V.
The control has three settings: Auto, 0 and Manual. This allows you to operate the pump according to the set program, switch it off or choose manual operation. The box also has a protected output for two underwater lights.
Automatic pump operation with a 24-hour timer
With the programmable timer, you set the daily switching times of the pool pump. In automatic mode, the pump follows this program. This ensures that filtration takes place at fixed times, without having to operate the pump yourself every time.
For a temporary deviation from the program, use the manual setting. With the zero setting, you switch off the operation. A separate time program for the lighting is not mentioned in the product information.
Motor protection matched to your pump
The type C version has an adjustable motor protection device of 4 to 6.3 amperes. The setting must match the rated motor current of the connected pump.
Various versions are available within the AstralPool range. Types A and B have a lower setting range; type D has a higher range. The right choice depends on the motor current, supply voltage and connection method of the pump.
Comparison of AstralPool control box types A through D
The table below shows the values from the provided model overview.
Item number in overview
Type
Motor protection setting range
Pump power 1-phase 230 V
Pump power ‘2-phase 400 V’*
Pump power 3-phase 230 V
74991
A
1.6–2.5 A
¼ HP
¾–1 HP
½ HP
74992
B
2.5–4 A
½ HP
1.5–2 HP
¾–1 HP
74993
C
4–6.3 A
¾–1 HP
3 HP
1.5 HP
74994
D
6–10 A
1.5 HP
4 HP
2–3 HP
The designation ‘2-phase 400 V’ has been taken literally from the provided overview. Have the correct connection method confirmed using the official wiring diagram.
This product page concerns item 69922 with a 630 W / 12 V transformer. The comparison overview lists other item numbers. Therefore, use the table to compare the specified motor ranges; the table does not confirm that those models have the same transformer or scope of delivery.
For a 1-phase 230 V pump, the overview lists a power of ¾ to 1 HP for type C. Always also check the rated current on the pump's nameplate: the power in HP alone is insufficient to choose the correct control box.
Built-in transformer for underwater lighting
The built-in transformer provides 12 V and has a rated power of 630 W. The protected lighting output is intended for two suitable underwater lights.
Check whether the lights are suitable for the transformer and whether the total connected power remains within the permitted load. The cable length and cable cross-section must also be matched to the lighting.
Pump control and light power supply neatly together
The control box combines the pump operation, motor protection and lighting transformer in one enclosure. This ensures an orderly setup of these components of the pool installation.
Before installation, check the mounting conditions and the protection class of the box. This data determines where and under what conditions the control box may be installed.
The Ramses filter box brings together the most important components of your pool filtration system in a compact enclosure. With a 550 mm Aster sand filter, a 6-way valve and a Sena pump, this pre-assembled installation offers a practical solution when space for pool equipment is limited.
According to the provided product information, the filter box is suitable for pools with a maximum volume of 80 m³. The pump, filter and internal piping are already installed. This means you do not have to assemble the individual components into a filtration system yourself, and connecting it to the pool piping is made easier.
Compact solution for limited equipment space
When installing a pool, there is not always enough space for a large equipment installation. The Ramses filter box combines the filtration components in a single enclosure, allowing the available space to be used efficiently.
The enclosure protects the pump, filter and valve from the elements. However, ensure there is sufficient space for connection, operation and maintenance when choosing the location. Even a compact installation must remain easily accessible.
550 mm Aster sand filter with Sena pump
The installation consists of an Aster Top-Mount sand filter with a diameter of 550 mm and a 0.63 kW Sena pump operating at 230 V. The pump circulates pool water through the filter, where dirt particles are trapped in the filter medium. The filtered water then flows back to the pool via the return pipe.
The specified maximum pool volume is 80 m³. Actual suitability also depends on pipe length, height differences, pipe resistance and the required daily filtration.
Pre-assembled piping with ball valves
The internal piping is pre-assembled up to the connection points of the filter enclosure. The three inlets to the pump and the return connection are each equipped with a ball valve. This allows the connected pipe sections to be shut off individually.
This setup simplifies the connection to the pool. The external pool piping and electrical supply still need to be connected to the installation.
Easily accessible 6-way valve on top
The 6-way valve is located on top of the filter. This Top-Mount design reduces the space required next to the filter and allows operation from a higher position.
Using the valve, you can select the filter's various operating modes, including filtration and backwashing. Leave sufficient space above the installation to operate the valve and perform maintenance. Switch off the pump before changing the valve position.
