W'eau Heater Cleaner heat pump cleaner

Keep your pool heat pump clean and ensure it continues to perform optimally with the W'eau Heater Cleaner Heat Pump Cleaner - 1 liter. This special cleaner has been developed for maintaining important parts of the heat pump, including the evaporator, condenser, and the fin grille.

While using a heat pump, large amounts of outside air are drawn through the unit. As a result, dust, pollen, leaves, and other debris can accumulate between the fins over time. When the fin grille becomes clogged, air cannot flow through the heat pump as easily. This can impair performance.

With the W'eau Heater Cleaner, you can remove this dirt in a safe and simple way. Spray the cleaner onto the fins, let it soak for about 10 minutes, and then carefully rinse it off with a normal garden hose.

Specially developed for heat pumps

A pool heat pump extracts heat from the outside air. To do this, sufficient air must be able to flow through the evaporator continuously.

However, the fine fins at the back of the heat pump can easily become clogged with substances such as dust, pollen, sand, and other environmental debris.

The W'eau Heater Cleaner is specifically intended to clean these parts without the need for aggressive mechanical cleaning methods.

For optimal air circulation

A clean fin grille is important for proper air intake.

When there is a layer of dirt between the fins, the heat pump has to work harder to draw sufficient air through the evaporator. By cleaning the grille regularly, you ensure that air can continue to flow through the heat pump easily.

This helps the heat pump to continue operating as efficiently as possible.

Cleans the evaporator, condenser, and fin grille

The W'eau Heater Cleaner can be used to clean key components of the heat pump, including:

• Evaporator
• Condenser
• Fin grille

The fins in particular require extra attention. They are thin and relatively fragile, and can easily be damaged if cleaned incorrectly.

That is why it is important to use a suitable cleaner for this and to rinse the fins gently.

Easy to apply with spray nozzle

The bottle is equipped with a practical spray nozzle that allows you to distribute the cleaner evenly over the fins.

Spray the product from top to bottom over the surface to be cleaned until an even layer is formed.

This means you do not need to use brushes or other hard materials between the fragile fins.

Let it soak for just 10 minutes

After application, let the W'eau Heater Cleaner soak in for about 10 minutes.

During this time, the product can loosen the accumulated dirt. Then, gently rinse the treated parts clean with a normal garden hose.

Do not use a high-pressure water jet.

Leaves a protective layer

The W'eau Heater Cleaner not only cleans but also leaves a protective layer on the fins.

This protective layer helps prevent new contamination, allowing the parts to stay clean longer.

For optimal results, it is recommended to repeat the treatment a few times throughout the year.

Helps maintain the efficiency of your heat pump

A dirty evaporator can reduce airflow through a heat pump. This can make the unit function less efficiently.

Regular cleaning is therefore important, not only to keep the heat pump tidy but also as part of proper technical maintenance.

With the W'eau Heater Cleaner, you help ensure that the heat pump can continue to draw in sufficient air and perform as well as possible.

Can contribute to a longer lifespan

A pool heat pump is a significant investment. Good maintenance is therefore important.

By removing dirt regularly, you prevent the evaporator and the fin grille from remaining heavily soiled for long periods.

A clean heat pump can function more efficiently, and regular cleaning can thus contribute to preserving and extending the lifespan of the unit.

How to use W'eau Heater Cleaner?

Switch off the heat pump completely before you begin maintenance.

Then spray the W'eau Heater Cleaner evenly from top to bottom over the fins. Ensure the product is well distributed.

Let the cleaner soak in for about 10 minutes.

Then gently rinse the treated parts clean with a normal garden hose. Do not use a high-pressure water jet and be careful with the fragile fins.

Allow the heat pump to drain and dry sufficiently after cleaning before using it normally again.

For proper maintenance, you can repeat this treatment a few times a year. How often cleaning is necessary depends on the environment where the heat pump is located. If there are many trees, dust, pollen, or other debris, more frequent cleaning may be needed.

Never use a high-pressure cleaner

For cleaning the fins, never use a high-pressure cleaner.

The fins of a heat pump are thin and can easily bend or become damaged due to the high water pressure. Damaged fins can subsequently impede airflow through the evaporator.

A normal garden hose with a gentle water stream is sufficient to rinse off the Heater Cleaner and the loosened dirt.

Using a vacuum cleaner on or between fragile parts is also not recommended.

Ideal for maintenance before and after the swimming season

A practical time to clean the heat pump thoroughly is at the beginning and end of the swimming season.

After an entire season, quite a bit of dust, pollen, and other contamination can have accumulated.

By letting the heat pump enter the winter clean and checking it upon restarting, you keep the unit well maintained.

Depending on the environment, an extra cleaning during the season may be wise.

1 liter content

The W'eau Heater Cleaner is supplied in a generous 1 liter package.

Thanks to the spray nozzle, you can apply the agent specifically to the parts that need cleaning.

This makes the product suitable for periodic maintenance of your pool heat pump.

Keep your pool heat pump in optimal condition

With the W'eau Heater Cleaner Heat Pump Cleaner - 1 Liter, periodic maintenance of your pool heat pump becomes simple. The cleaner removes dirt from the evaporator, condenser, and finned grid, allowing the heat pump to continue drawing in sufficient air.

Spray the Heater Cleaner onto the fins, let it soak for approximately 10 minutes, and then rinse carefully with a garden hose. This helps maintain the heat pump's efficiency and ensures your system remains well-maintained season after season.