WYBOT S2 Solar cordless pool robot with solar charging station

The WYBOT S2 Solar is a cordless pool robot that cleans the pool floor, walls, and waterline. The system consists of a powerful pool robot and a magnetic solar charging station that is permanently installed on the edge of the pool.

After a cleaning program, the robot can automatically return to the charging station. Once the remaining battery charge drops below approximately 20 percent, it will attempt to reach the station to recharge wirelessly. The solar panel provides energy to the charging station. As a result, for regular maintenance, you do not need to remove the robot from the pool after every cycle and charge it manually.

For situations where there is insufficient sunlight, a power adapter is also included. This allows the battery to be charged in approximately three hours. The combination of solar energy and mains power makes the S2 Solar suitable for daily maintenance and more intensive cleaning after a period with a lot of debris.

Cleaning of floor, walls, and waterline

The WYBOT S2 Solar vacuums up loose debris from the pool floor and uses a high-speed front brush to loosen stubborn dirt. The robot can climb suitable pool walls and move along the waterline.

It is suitable for various pool surfaces, including:

• Cement and concrete

• Pool liner

• Mosaic

• Tiles

• Other common hard pool finishes

Performance on walls and at the waterline depends on the pool's finish, shape, slope, and smoothness. Very slippery walls, sharp corners, high steps, or irregular transitions can affect grip and routing.

Seven cleaning programs

Via the WYBOT app, you can choose from seven programs:

• Full pool: cleans the floor, walls, and waterline

• Floor only: targeted program for the pool floor

• Walls only: cleans the vertical pool walls

• Waterline only: moves along the top edge of the water

• Walls then floor: one combined cleaning cycle

• Eco-floor mode: energy-efficient cleaning of the floor

• Turbo-floor mode: more intensive floor cleaning with extra suction power

By choosing a program that matches the debris levels, the available battery capacity is used more efficiently. For example, when there is mostly sand and leaves on the floor, the robot does not need to waste energy cleaning the walls.

Scheduled cleaning

In the app, you can set a cleaning schedule. The robot will then start automatically at the chosen times. Afterward, it will attempt to return to the solar charging station.

This allows the S2 Solar to remain in the pool for extended periods and perform periodic maintenance. The filter basket still needs to be emptied and cleaned manually. Additionally, if there is insufficient sunlight, intermediate charging using the included power adapter may be necessary.

Automatic return and charging

When the battery is low, the robot searches for the charging station. The magnetic connection helps it get into place for wireless charging. The success of this process depends on the correct installation of the station and the shape of the pool.

According to the manual, the charging station requires a level location with a water depth of at least 1.2 meters. Directly below the station, there should be no stairs, seating areas, lighting, or other obstacles. The solar panel must receive sufficient direct sunlight.

Dual filtration

The 3D filtration system consists of two layers:

• A 180-micron filter basket for leaves, insects, twigs, sand, and other visible debris

• A fine 40 PPI filter sponge for smaller dirt particles

The dirt remains in the removable filter basket. After cleaning, open the robot, remove the basket, and rinse both filter layers with clean water. Regular cleaning is important to maintain suction power and water flow.

The pool robot does not replace the circulation pump, water treatment, or fixed pool filter. Dissolved substances, algae, and very fine contaminants must still be addressed by the regular pool system and proper water treatment.

Powerful, brushless drive

The brushless motor has a stated average water displacement of 3,962 gallons per hour, approximately 15 m³ per hour. The brushless construction is designed for high efficiency and less mechanical wear.

The robot moves at approximately 10 meters per minute and uses various route patterns to clean the selected zone. Actual coverage depends on the pool shape, obstacles, pollution level, and selected program.

Wireless control via the WYBOT app

The S2 Solar can be connected to the WYBOT app via Bluetooth. The app provides access to features including:

• Choice of seven cleaning programs

• Setting a cleaning schedule

• Manual control

• Checking status and battery charge

• Returning to the charging station

• Software and firmware updates

Because communication underwater is more limited than above water, the connection may be temporarily interrupted. To adjust certain settings or perform updates, it may be necessary for the robot to be in the charging station or taken out of the pool.

Package contents

• WYBOT S2 Solar pool robot: 1 piece

• Solar charging station: 1 set

• Solar panel and associated floating components: 1 set

• Floating blocks: 2 pieces

• 180-micron filter basket: 1 piece

• Fine filter sponge: 1 piece

• Power adapter: 1 piece

• Retrieval hook: 1 piece

• User manual: 1 piece